# Cut file help and torch stutters when lowering lately
**URL:** https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215
**Category:** General Discussion
**Created:** [April 6, 2023, 11:46am UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215 "2023-04-06T11:46:47Z")
**Posts on this page:** 5
**Page:** 1
### Author:  [@92blewbyu](https://forum.arcdroidcnc.com/u/92blewbyu)
#### Post date: [April 6, 2023, 11:46am UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215/1 "2023-04-06T11:46:47Z")
Good Morning ,
Im looking for a little help with a cut file that is giving me some grief for a few weeks . When i look at this file in Inkscape, Sheetcam , E machine i do not see the first issue . My laptop does not allow me to run Fusion currently , That being it makes 4 random pierces above my file , second is the machine pierces, cuts stops lifts plunges re-pierces and begins cutting on certain letters its cutting out when it could be in the original path of cut. I need to make 2 of these one at the largest i can within the reach of the Arcdroid second will eventually be 18" high 68" wide once i figure this out.
[getting Loosefinal.dxf](https://forum.arcdroidcnc.com/uploads/short-url/6BDRusdUYaogQSVEdJtg4QjTGPo.dxf) (26.9 KB)
---
### Author:  [@mikehammer](https://forum.arcdroidcnc.com/u/mikehammer)
#### Post date: [April 6, 2023, 12:29pm UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215/2 "2023-04-06T12:29:58Z")
I had a quick look at your file in CorelDraw, I can see 3 nodes above your image.
That is causing your random pierces.
---
### Author:  [@92blewbyu](https://forum.arcdroidcnc.com/u/92blewbyu)
#### Post date: [April 7, 2023, 12:29am UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215/3 "2023-04-07T00:29:54Z")
Thank you how can i remove them if i don’t see them to edit them?
---
### Author:  [@mikehammer](https://forum.arcdroidcnc.com/u/mikehammer)
#### Post date: [April 7, 2023, 2:19pm UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215/4 "2023-04-07T14:19:49Z")
I’ve never used Inkscape, so exact instructions wouldn’t be possible from me. Once I ungrouped the image they were visible for me in CorelDraw. I have attached your dxf with those nodes removed and no other changes.
[getting Loosefinalnodesremoved.dxf](https://forum.arcdroidcnc.com/uploads/short-url/nmhf1TZjAHis3UMWxJRMP5E3Cwz.dxf) (354.1 KB)
---
### Author:  [@92blewbyu](https://forum.arcdroidcnc.com/u/92blewbyu)
#### Post date: [April 7, 2023, 9:20pm UTC](https://forum.arcdroidcnc.com/t/cut-file-help-and-torch-stutters-when-lowering-lately/2215/5 "2023-04-07T21:20:52Z")
i GREATLY appreciate your help! Thank You